Iqbalgsm Worldwide delivery Trusted by 5,000+ technicians
Iqbal GSM

Suggestions

Products

Search for “” →
Shop All Part Request Wholesale Membership

Categories

2UUL TOOLS YF BATTERY CABLE Maant Mijing Fold flex cable Flip flex cable Soptop LCD FPC CONNECTOR BATTERY CONNECTOR IG PRODUCTS Octopus
Account
PMI632-502  IC
In Stock

PMI632-502 IC

4.0 (12 reviews)

As low as

Rs 180.00

Worldwide shipping · Cash on Delivery

Quantity
Unit price Rs
Quantity
Total Rs
Ask on WhatsApp
Seller: Iqbal GSM

Product Details

====================================================================================================

           QUALCOMM PMI632-502-00 SUB-PMIC / CHARGING & LIGHT IC REPAIR GUIDE

====================================================================================================

1. PRODUCT IDENTIFICATION & SILICON SPECIFICATIONS:

----------------------------------------------------------------------------------------------------

- Silicon Laser Marking:          PMI632 [Line 2: 502-00 or 502]

- Commercial Hardware Name:       Qualcomm Intermediate Power Management Subsystem (PMI632)

- Silicon Manufacturer:           Qualcomm Technologies, Inc.

- System Classification:          Secondary Power Management IC (Sub-PMIC / Charger / Backlight)

- Associated Main Platforms:      Qualcomm Snapdragon 439, 450, 632, 636 platforms

- Companion Primary PMIC:         Qualcomm PM439 / PM8953 / PM6125 (depending on logic board)

- Package Form Factor:            Fine-Pitch 72-Pin BGA (BGA72 / WLCSP)

- Subsystem Blocks Inside PMI632-502:

  * High-Efficiency Switching Battery Charger:

    - Supports 5V / 9V Quick Charge (QC) standards with programmable charge current limit.

  * System Power Generation:

    - Primary system bus converter generating VPH_PWR / VSYS (3.7V – 4.2V DC).

  * High-Voltage Display WLED Backlight Driver:

    - Integrated boost converter raising 3.7V battery voltage up to 18V – 25V DC.

    - Integrated multi-channel current sinks for cathode return lines.

  * Camera Flash & Torch Driver:

    - Integrated current source for dual/single white LED flash.

  * Battery Management & Fuel Gauge:

    - Integrated coulomb counter and battery temperature ADC monitoring.

  * USB Detection & 5V OTG Step-Up Boost:

    - USB CC/ID detection, Type-C logic, and reverse boost converter for USB peripherals.

2. COMPATIBLE SMARTPHONE PLATFORMS (502-00 SPECIFIC):

----------------------------------------------------------------------------------------------------

- Xiaomi / Redmi:

  * Redmi 7 (Snapdragon 632)

  * Redmi 7A (Snapdragon 439)

- Oppo / Realme:

  * Oppo A3s (CPH1803, CPH1853), Oppo A5, Oppo A7

  * Realme C1 (RMX1811)

- Vivo:

  * Vivo Y91 / Y93 / Y95 (Qualcomm Snapdragon 439)

  * Vivo Y11 2019 (Snapdragon version)

- Samsung:

  * Galaxy A01 (SM-A015F/G/M Snapdragon edition)

*(Caution: Substituting 502 with 902 or vice versa may cause backlight failure or battery logo boot-hangs 

  due to differences in internal firmware profiling and display driver register mapping)*

3. TYPICAL BOARD-LEVEL FAULT SYMPTOMS:

----------------------------------------------------------------------------------------------------

- Completely Dead Phone (0.000A or 0.020A Stuck Current on DC Bench Supply):

  * When PMI632 fails, VPH_PWR is not generated. The main PMIC and CPU receive zero power, leaving 

    the device completely non-responsive.

- Fake Charging / Slow Charging / Battery Percentage Drops while Plugged In:

  * Phone displays the charging lightning bolt icon, but current draw from USB charger stays at 

    0.00A – 0.15A; internal switching MOSFET or boot diode inside PMI632 is blown.

- Black Screen with Vibrations & Sound (Display Backlight Failure):

  * Device powers on normally, plays boot ringtone and receives calls, image is visible under a strong 

    flashlight, but backlight remains dark (burned boost diode, boost coil, or internal driver in PMI632).

- "Battery Temperature Too Low / Too High" Pop-up Warning:

  * Phone refuses to charge and shuts down with temperature warning due to damaged battery ID/thermal ADC 

    circuit inside PMI632.

- Short Circuit on Primary Battery Rail (VPH_PWR Short to GND):

  * Upper buck MOSFET failure clamps VPH_PWR rail directly to Ground (0.000V in diode mode), causing 

    the DC power supply to beep / trip on connect.

4. STEP-BY-STEP MULTIMETER TESTING & DIAGNOSTICS:

----------------------------------------------------------------------------------------------------

A. Cold Testing (Diode Mode Check - Board Unpowered, Battery Disconnected):

   1. Connect Multimeter RED probe to Motherboard Ground (GND), probe with BLACK probe:

      - VBUS Input Filter Capacitor (near USB input): Normal ~450mV – 550mV.

      - Battery Connector Pin (VBAT Positive): Normal ~400mV – 480mV.

      - VPH_PWR Main Inductor (large coil adjacent to PMI632): Normal ~350mV – 450mV (0.000V = dead short).

      - Backlight Boost Inductor / Anode Diode: Normal ~400mV – 500mV.

      - Boot Capacitor (BST): Measure across both capacitor terminals; must NOT beep (no short).

   2. Short-Circuit Isolation:

      - If VPH_PWR coil reads 0.000V in diode mode, inject 3.7V DC (limited to 2.0A) directly to VPH_PWR. 

        Observe under thermal camera: if PMI632 glows instantly, desolder the chip.

B. Live Operating Voltage Check (Hot Testing):

   1. Connect 5V USB charger cable to the phone:

      - VBUS Test Point: Must read steady 5.0V – 5.2V DC at input capacitor.

      - VPH_PWR Coil: Must output steady 3.7V – 4.2V DC (even with battery unplugged).

      - Battery Connector: Must output 3.7V – 4.35V pulsed charging voltage.

   2. Power the phone on:

      - Backlight Anode line: Should read 3.7V in standby, then jump to 18V – 25V DC once the screen 

        turns on. If it stays at 3.7V, PMI632 boost switching circuit is defective.

5. SOLDERING, REBALLING & REWORK SPECIFICATIONS:

----------------------------------------------------------------------------------------------------

- Thermal Shield Removal & Neighboring Component Safety:

  * PMI632 is usually protected under a soldered RF shield canopy near the CPU/eMMC/UFS flash memory.

  * Always apply Kapton thermal tape and shielding coins over the CPU and memory chips before rework.

- IC Removal:

  * Dispense high-purity RMA BGA flux around PMI632.

  * Hot air rework station setup: 320°C – 335°C, medium airflow (35% – 45%).

  * Circle the nozzle uniformly over the chip for 30–40 seconds. Once solder balls liquefy, lift chip cleanly.

- PCB Pad Cleanup:

  * Apply 183°C (Sn63/Pb37) leaded solder to lower pad alloy melting threshold.

  * Flatten pad matrix using copper wick braid with iron tip at 290°C – 300°C.

  * Clean flux residue using 99% Isopropyl Alcohol (IPA); inspect pads under microscope.

- Reballing Procedure:

  * Use a dedicated or universal 0.12mm BGA stencil matching the 72-pin PMI632 footprint.

  * Squeegee 183°C leaded solder paste uniformly into stencil apertures.

  * Heat gently at 280°C with low airflow (20%) until uniform solder spheres form.

- Placement & Alignment:

  * Spread a thin, transparent layer of tacky BGA flux onto logic board pads.

  * Align Pin 1 dot on PMI632 with motherboard silkscreen marking.

  * Reflow at 310°C – 320°C with 35% airflow; observe the chip pull into place by solder surface tension.

  * Allow PCB to cool naturally for 3–5 minutes before plugging in battery or USB power.

====================================================================================================